GN Oil Drilling Solids Control Equipment

The Swaco variable speed 518 centrifuge has the control flexibility to delivereffective solids/liquids separation for the varying conditions encountered through out most drilling programs. Infinitely adjustable main Decanter Centrifuge and conveyor speeds coupledwith the ability to increase or decrease conveyor differential , provide completecentrifuging ra nge capability with a single unit.

shale shaker speed can vary from 0 – 3250 rpm to increase particle separation
(cutpoint) for improved solids removal and cleaner effluent.
Differential speed can be regulated to improve solids conveyance or obtain
dryer discard through the variable speed panel.
Main bowl and conveyor speeds are infinitely controllable within specified
operating ranges.
The liquid radius in the decanter can be changed to obtain either a wet/dry
solids discard or cleaner effluent.
Speed adjustments are done through the Variable Frequency Panel that is
separate from the centrifuge.
Bowl torque monitoring adjusts pump speed to eliminate plugging of unit.
Increased horsepower and coffin modifications allow for feed rate volumes
up to 800Lpm.
Heavy duty 50 Hp main drive motor replacing the 30 Hp.
20 Hp motor on back drive replacing the 7.5 Hp.
New tie down lid , required only one wrench and no nuts and bolts.
Simple start / stop switches for easy start up and shut down of centrifuge and
pumps.
Cost Effective
The VS 518 effectively removes the finest of silts and returns the expensive
fluid for re-use within the system. Minimizing cost for make up fluids ,
dilution , cleanup and disposal..

The dust on the casing should be cleaned periodically.Before operation the fix bolts of the motor should be checked to see if they are loosened. If so, they should be fixed tightly before use.

Check to see if the service cable is rubbed, buried or squeezed.A good lubrication of the drilling waste management should be ensured during their operation.An appropriate amount of high temperature lubricating grease LGHP2 by SKF was injected for the bearing before its assemblage, with it’s working temperature between -40～200°C.No less than 25.8g lubricating grease LGHP2 should be injected into each bearing for every 2000 hours.

 When Mud Cleaner is found that temperature of the bearing is 10℃ higher than its average daily temperature (meaning that the so-called risen temperature is that measured at the bearing location of motor casing on-the-spot subtracts from the outside environmental temperature) in 2000hours, Mud Agitatorshows that the bearing is lacking of lubrication, the lubricating period and the amount should be both reduced.

Gnsolidsamerica is the author of the article on drilling waste management and mud system,find more information about http://www.gnsolidsamerica.com/drilling-mud-circulating-system.html.

mud agitator manufacturer STRUCTURE and MAIN PARTS Refer the drawing below to find more details of the structure. The main parts is: main vessel, pipeline for mud and gas, structural basement, pressure gauge valves and adapters and so on. Manhole is on the vessel, for maintaining or repairing. SN Des. PN QTY 1 Main vessel GNZYQ1000-01 1 2 Valve 16DN250DD3 1 3 Nipple DN250DC-00 1 4 Bolts 8 5 Nipple DN100DC-00 1 6 Valve 16DN100DDB 1 7 Bolts 8 8 Elbow GNZYQ1000-02 1 9 Seal DN200PN10 1 10 Bolts 16 11 Nipple DN200DC-00 1 12 Bolts M24x300 4 13 Pressure gauge YLB100 1 Poor boy degasser structure 7) OVERALL DIAMENTION： II、ASSEMBLE and PREPAARATION 1）Lifting, Transportation, Assembling When lifting, keep the main vessel straight and vertical, keep slowly moving. When transporting, it can be horizontal lying, while have to keep the two legs of the vessel supporting the other side, while one side is the base structure. Usually the poor boy Degasser should be mounted beside the mud tank, under the basement, should be firm and strong, foundation bolt is used to keep the safety, as drawing below. 1、Poorboy degasser base 2、Foundation bolt 3、Concrete ground When assembling, the crane lift the degasser up, slowly and straight to the concrete ground, use wire rope from three direction to keep it firm steady, ensure the main vessel vertically stand, then strength the foundation bolt. 2）Preparation before Operating When it is well assembled, properly arrange the vent line, usually prepared by client. Connect the inlet with BOP or choke manifold. Close the dump valve, open the outlet valve and connect with the shaker or the mud tank. 3) Movement Before move the degasser pls click to know, dissemble the pipeline first, then release the wire rope, lift from the top by crane, loose the foundation bolt. gnsolidsamerica is the author of the article,pls refer Mud Agitator to know more

GNPS703D Shale shaker Operation and maintenance instruction come from TANGSHAN GUANNENG MACHINERY EQUIPMENT CO., LTD. 1. Summarize 2. GNPS703D Shale shaker structure 3. GNPS703D Shale shaker technical parameters 4. GNPS703D features 5. Lifting, transportation and installation 6. Operation on shale shaker 7. Shale shaker Maintenance 8. Spare parts for GNPS703D 9. Enclosed files for GNPS703D Summarize 1. Decanter Centrifuge is high efficiency shaker. It is designed according to users’ actual demand based on modern technique and principle. GNPS703 takes advantage of double vibration motors in-phase principle. It holding ideal design on structure, and work steadily, operated lasting time without any problem, take rather little cost on maintenance. If choose proper model or parameters, it can work for many kinds of drilling fluid solids control. It is an ideal solution for Oil and gas drilling, HDD, Metallurgy, mining tail mud solids control 2. GNPS703 Shale shaker structure Please find GNPS703 shaker structure as fig I. It contains pedestal, shaker deck, tension wedge, shaker screen, rubber strip, deck adjustment device, baffle box, tension device, electric cabinet, vibration motor, damping spring. Fig I. GNPS703 Shale shaker structure Shale shaker GNPS703 can be used by single or designed as tandem and triplex shaker to be operated at drilling job site 3. GNPS703 Shale shaker technical parameters Model: GNPS703 Vibration: Balanced elliptical motion Vibration amplitude: 7mm (double type) Motor power: 1.0+1.94kW Treating capacity: 150m3/h Screen area: 2.2m2 Screens: 700×1250mm×3 10~200 mesh (Frame screen or Pyramid frame screen) Dimension: 2783×1880×1254mm Weight: 1980kg 4. GNPS703 features (1) GNPS703 Shale shaker is designed as double motors in-phase principle. The shale shaker will vibrate as elliptical, part of spare parts are interchangeable with international shale shaker (2) Adopts advanced vibration motor, reliable operation, run long time without any problem (3) The Decanter Centrifuge can be flat type or pyramid type. Shaker deck can fix 3 pieces screen and make screens as different combination. This will lead screen take longest usable life. According to different drilling mud the screen mesh will be 40-200 mesh,can be flat type or pyramid type. decanter centrifuge for sale can fix 3 pieces screen and make screens as different combination. This will lead screen take longest usable life. According to different drilling mud the screen mesh will be 40-200 mesh, click here to get more information (4) Screen is tensioned by wedge, this is more convenient and reliable (5) The shaker deck can be adjusted. Adjustment will be realized by adjusting worm whirl. There is worm whirl at each side of shaker deck. Middle shaft connect two whirl pipe, when we make adjustment, two sides will be compliant and in-phase (6) The paint of shaker is processed by grit blast, use high anticorrosive zinc rich coating. Will make shaker surface anticorrosive and more beautiful.

GNZJ752—2S Desander is combine solids control equipment which developed, designed and manufactured by our company. It is combined of first stage solids control equipment shale shaker and second stage solids control equipment 10″desander cyclones The main features of GNZJ752-2S are reliable in working ,convenient in maintenance and space saving . It is one of the ideal solids control facilities.

This facility is composed of seven main parts: shale shaker GNZS752, support bracket ,desander pipe ,desander cyclones, discharge trough , Decanter Centrifuge, explosion-proof electric control panels and so on. 1.Mpa pressure gauge   2. Explosion-proof electric control panel 3. Desander cyclones 10″ 4.Discharge troug 5.GNZS752 linear shale shaker 6.Desander pipe 7. Support bracket

The facility has adopted great amount of the latest technology of the world . It is compact in structure ,reliable in working, convenient in  maintenance, and can be applied in many fields. It is the assembly of a shale shaker; desander cyclones. It reduces the occupation, and make it a great convenient for on-site operation and well group-moving.

Gnsolidsamerica is the author of the article on Desander andDecanter Centrifuge,find more information about shale shaker.

A continuación se presentan las fotos tomadas en GN solids control situarse en CIPPE 2014. Una gran cantidad de clientes internacionales nos visitan y mostró interés en nuestros equipos de control de sólidos y gestión de residuos.

We already attended CIPPE for 6 times from 2009 to 2014, every year we showed our advanced technology equipments.
GN zarandas con ajuste del ángulo eléctrico y ajuste machanical
GN decantador centrífugo con panel de control PLC para recuperación de barita

GN limpiador de lodo con 4 Mongoose mallas

GN secador vertical de recortes

GN centrífuga decantadora de gran tazón grande capacidad

Debido a que la exposición CIPPE aceite se lleva en Beijing, capital de China, es un poco lejos de los clientes en América, no tantos clientes visitan. Vamos a mostrar los mismos equipos en la OTC 2014 en Houston, la bienvenida a clientes de América a que nos visite en Houston y comprobar nuestros equipos.

La centrífuga 3(tres)-fase esta diseñada para la separación de productos que contengan 3 (tres) fases, de diferentes densidades, por ejemplo: un sólido, agua y aceite.

GN solids control puede proveer la centrífuga 2(dos)-fases que son sólido fase y líquido fase. Tenemos inventarios de Centrífuga decantadoras en Houston, Colombia, Argentina y Chile. Su especificación de la siguiente:

Modelo :GNLW363VFD con PLC(Unidad de frecuencia variable)

 Capacidad de la Centrífuga (Max) 200GPM

Capacidad de la Centrífuga (Normal) 132GPM

Diámetro del tambor 14 inch

Longitud del tambor  50 inch

Velocidad típica del tambor: 0~3200RPM

 Fuerza G (Máx) 2062 @ 3200RPM

 Punto deseparación  2~5µm

 Motor principal  37KW (50HP)

 Conducción en reversa  11KW (15HP)

Este es nuestro mejor modelo de centrifuga más vendido en el mundo. Si usted necesita un centrífuga decantadora  con el tazón 14inch, por favor en contacto con GN solids control.

 

GN solids Ameirca tiene un almacén en Houston, y tiene zaranda vibratoria, Mallas zarandas, centrífuga decantadora del velocidad variable y centrífuga decantadora del alta velocidad en stock.

La centrífuga decantadora (decantadora) tiene un amplio campo de aplicaciones en varios procesos donde continuamente deben ser separadas una fase líquida y una sólida.
Principio de funcionamiento:
La centrífuga es alimentada a través de un tubo estacionario, el cual se encuentra dentro de un eje hueco conectado al transportador helicoidal giratorio (espiral). Luego entra en un compartimiento de alimentación y es acelerado a través de ranuras de alimentación dentro de la tina giratoria. Una vez dentro de la tina, las fuerzas centrífugas aceleran los sólidos pesados, donde se sedimentan en la pared de la tina. El líquido más ligero llena la tina hasta el nivel del dique de vertido (vertederos).

Bienvenido a visitar nuestro almacén y ver nuestra centrífuga decantadora.  En la jornada inaugural de la compra será un gran descuento.

GN solids control produce the complete line solids control equipments, also the spare parts for solids control, including: Shaker screens, hydrocyclones ( desander cone, desilter cone), special parts(feeding pipe for decanter centrifuge, gear box, nozzle for mixing hopper, wedge for shale shaker ,etc) ,Universal parts (bearings, oil seal, electric motors, vibration motors, etc.).
We have our own shaker screen factory which can provide not only screens for GN own shaker models( GNZS703, GNZS594), but also for other brand shakers, like Derrick FLC500, 48×30, MI-SWACO Mongoose PT, Brandt Cobra families, Kem-tron, FSI, etc. We can provide both flat screens and pyramid screens, also we provide both hook strip screens and also steel frame screens, composite material screens.

Welcome to inquiry solids control spare parts to GN solids control.

GN Solids Control will attend 16th Colombia Oil & Gas Show (XV Congreso Colombiano de Petróleo y Gas 2013) in Bogota.

Date: Noviembre 20 al 22 de 2013

Stand No.: International Pavilion Hall, 616A

Location: Bogota,Colombia

Address: Centro Internacional de Negocios y Exposiciones, Main Entrance Carrera 37 No 24 – 67

We will show GNLW363G high speed decanter centrifuge, this is our best sold model .If you are interested in the decanter centrifuge, welcome to visit our booth and check our equipments there. 

Features of GNLW363G centrifuge:

1 14inch diameter bowl

2 screw conveyor protected by tungsten carbide tiles

3 solids discharge port protected by tungsten carbide ring

4 VFD control panel is optional