GN Oil Drilling Solids Control Equipment

Weighting materials are a high-specific gravity and finely divided solid material used to increase the density of a drilling fluid.  How to add weighting materials to the drilling fluids?

In most oil & gas drilling solids control system, there are weighting tank, which has a mud hopper and mixing pump, the operator add the additives from the top of the venturi hopper, the mixing pump transferred the drilling fluids through the cross under the hopper, under the working of pressure, the power material are added to the drilling fluids. It will be mixed by mud agitator installed on the tank. Sometimes shear pump will be used instead of centrifugal pump.

GN designed 1000gpm mud cleaning system including the following equipments:

2sets of GNZS703 shale shaker or GNPS703 shale shaker, 1 set of GNZJ703 mud cleaner, 2 units of mud agitator, 1 mud hopper, 3 sets of centrifugal pumps, 3 ea lights, 1ea mud tank 14.5meters length. This is standard design, we can revise it according to client’s particular requirement.

This 1000gpm mud cleaning system can be used for various applications, like HDD, CBM, even small rigs for oilfield. Welcome to contact GN for more details.

Cutting dryer/vertical cutting dryer is widely used for drilling cuttings management in the oilfield. Lubrication is important for cutting dryer’s maintenance. Manufacture will provide detailed lubrication diagram with the machine. Motor bearings are grease lubricated, the other bearings are all oil lubricated.

 The oil should be changed every 1600 hours of operation or every three months, whichever occurs first. To change oil, drain oil from the gear unit and drain pot. Gear unit plugs are located under the inside sheave. Oil can be drained from the drain pot by disconnecting the suction line at its union located left of the filter and above the pressure switch.

GNCD930 vertical cutting dryer user manual provide more info about the lubrication diagram.

GN produced decanter centrifuge for drilling fluids, bowl assy is the main body of the decanter centrifuge. Bowl assy including collection box, bowl, inner tube, screw propeller, gear box, hydraulic coupler, pulleys, bearings, etc.

Bowl is the most important component, in includes taper piece and straight piece, previous production procedure is to make them separately and connected by bolts, GN produced centrifuge bowl is one piece bowl, the connection is welding, such centrifuge bowl is more steadily in performance and working time.

There are mainly 2 type degasser used in oilfield, vacuum degasser and poor boy degasser.

Vacuum degasser is used in drilling solids control system to remove the gas such as methane, H₂S and CO₂ from the gas-cut mud, there are horizontal vacuum degasser, vertical vacuum degasser and atmospheric degasser.

Poor boy degasser is well control equipments, it is used to separate dangerous gas, and the vacuum degasser is used only when we need more effective and more efficient results.

GN designed GNLW363 decanter centrifuge with a two-stage planetary reducing gear box, also called differential.

There is internal gear on the shell. Shell rotate with the drum, and then left pulley drive 1-stage sun gear on the input shaft to rotate, at this time, 1-stage sun gear gear into inner gear through 1-stage planet gear, thus 1-stage revolving arm rotational speed is formed by rotational speed of shell and input axle, and this rotational speed was outputted to 2-stage through 2-stage sun gear. The transmission principle of the two stages are the same, at last, propeller begin to rotate driven by output shaft. Differential is the most complex and most important part of decanter centrifuge.

 

GN designed CD930 vertical cutting dryer is applied to drilling waste management system in the rig site. Basket is the main wear parts for cutting dryer, the picture below is cutting dryer basket.

Screen opening can be choose by various field test result. The basket material is stainless steel,inside the basket, there are screen, rotor wheel, they are the main components of cutting dryer.

The full name of ADIPEC is Abu Dhabi International Petroleum Exhibition and Conference which is held ) on 11 – 14 November 2012 at the Abu Dhabi National Exhibition Centre (ADNEC),most of the visitors are from Middle East and North Africa, also from many other countries in the world.

We will take our new decanter centrifuge there for the show, model GNLW363G, centrifuge bowl assy with stainless steel 304 and screw propeller protected by tungsten carbide tiles.

GN Solids control Booth. No.: Hall: 10 Stand:10035C, welcome to visit us if you will attend this show.

The Rig Vacuum system is powerful enough to suck just about anything off the ground, including mud, dirt, and liquids of every variety. Rig Vacuum system is designed to collect all drilled solids that are produced while your rig is drilling, effectively eliminating waste before it becomes a problem.

Rig mud recycling system can help to reduce drilling waste and separate drilling cuttings with fluids, it will help a lot for the vacuum unit.

High speed decanter centrifuge is widely used for oilfield drilling mud system, do you know how to test a centrifuge?　There are many important parameters for centrifuge, like rotary speed, vibration, bearing temperature increasing, pulley size, treating capacity, etc.

For a simply inspection tested by clean water, you should at least test vibration, bearing temperature and rotary speed. See the attached photos of inspection centrifuge, you can see where it located and how to test it.

The 2^nd step is to use bentonite mud to feed to the centrifuge, to test the performance and treating capacity of the centrifuge. If it is with VFD control panel, you can test it in various frequency during working.