Category: Uncategorized

There are a lot of mud tanks in drilling rig solids control system, during operation, some slurry with oil will deposit in the tank bottom. How to clean the mud tank become a problem, tank cleaning takes time and cost a lot.

To clean mud tank, firstly you should improve the agitating performance of the mud agitator to less the sediment;secondly, you can use a pitgun to carry out this process remotely, operators and rig owners no longer need to have personnel enter mud pits or tanks to manually break up compacted solids that build up on the floor, beneath pipework, and in tank corners during the drilling process.

GNLW453 centrifuge is GN standard 300gpm centrifuge with 17 inch bowl, bowl length 62 inch. Except for 200gpm centrifuge, we also have standard 14inch bowl centrifuge, 350gpm centrifuge , 400gpm centrifuge( 21inch bowl).

GN 300gpm centrifuge is designed for un-weighted drilling fluids processing, , max bowl speed can reach 3500r/min and 3000G maximum. By changing pulleys, you can get 2 different speed in different conditions.

Injection is a method of drilling waste disposal which is aim at “ZERO” discharge nominally. Slurry injection is one of the methods, it is grinding or processing solids into small particles, mixing them with water or some other liquid to make a slurry, and injecting the slurry into an underground formation at pressures high enough to fracture the rock. Including slurry fracture injection, fracture slurry injection, drilled cuttings injection, cuttings reinjection, andgrind and inject.

Drilling waste is composed of drilling fluids, cuttings, oil, chemicals that results from oil & gas drilling. Oil & Gas drilling bring up mud and other material with high hydrocarbon levels requiring special disposal practices.

Drilling waste can not disappear, only if there is drilling, these drilling waste will occur, what we can do is to less the waste by using better solids control equipments and proper management on the waste. The Environment protection dept. should regulate more for the drilling waste disposal.

The gearbox on the mud agitator has a pre-selected gear ratio to maximize the suspension of solids in solution. This gear ratio provides a great increase in torque that is transmitted to the impeller. Any object that might fall into or be placed in the mud tank runs the risk of being caught by and wrapped up by the agitator.

Before operating the mud agitator, you must confirm the direction of the gear box, otherwise it will damage the gearbox.

Gravel pack is a sand-control method used to prevent production of formation sand.

What is Sand Control ?

Sand control refers to managing/minimizing sand and fine production during petroleum production. Sand and fine produced with oil and gas can cause erosion and wear of production facilities/equipments, resulting in production downtime, expensive repairs, and potentially loss of containment.

In gravel pack operations, a steel screen is placed in the wellbore and the surrounding annulus packed with prepared gravel of a specific size designed to prevent the passage of formation sand. The primary objective is to stabilize the formation while causing minimal impairment to well productivity.

GN solids control focus on drilling fluids solids control,welcome to contact us.

GN shale shaker vibrator is Italy Oli brand vibration motor, which is with good quality and stable performance.

Linear motion shale shaker utilized 2pcs same power vibration motor, for example, GNZS703 use 2pcs 1.5KW vibrator. Their installation method is vertical.

Balanced elliptical motion shale shaker use 2 pcs different power vibration motor(1 large, 1 small), e.g. GNPS703 shale shaker use 1 pc 1.94KW + 1pc 1.0kw. Their installation method is horizontal in parallel.

Mud cleaner is used as the 2^nd and 3^rd phase separation of drilling fluids, used after shale shaker. After treated by mud cleaner, the clean drilling mud is re-used to the well, the cuttings are collected and enter into drilling waste management system.

 Mud cleaner is used before decanter centrifuge, it can separate most of the large solids and less the solids content in the mud, to less the burden of decanter centrifuge so that the service life of centrifuge can last longer.

As centrifuge is the most expensive equipments in solids control system. For this reason, a good mud cleaner is much more important. Some clients do not use under-flow shaker on the mud cleaner, they only use separate desander and desilter, then all the rest works are done by the centrifuge, it will damage very fast. Or some clients only use a small screen area mud cleaner, so some of the large cuttings leaked into the tank to damage the centrifuge screw propeller and feeding pump.

Drilling mud from rig overhead manifold flow to shale shaker, mud cleaner，the cuttings processed by shaker and mud cleaner is transferred by screw conveyor to vertical cutting dryer.

The solids processed by Vertical cutting dryer is discharged from solids discharge port, get recycled mud in mud recycling tank, which is pumped by centrifuge feeding pump to decanter centrifuge, the separated solids is discharged from centrifuge solids discharge port, the clean mud come back to solids control system.

Mud agitator lubrication including gear box lubrication, bearing lubrication.

Before operation, lubricate gearbox with L-CKE/P 220~320# worn gear oil . Verify that lubricant level in the gearbox reaches the bottom of the oil level plug.

Bearings should be cleaned and re-greased on the same schedule as oil changing. After cleaning, fill bearings to one-third of their free volume.

After 100 hours of initial startup, clean gearbox inside, add new grease oil. Then lubricated at every 2500-hour interval.